GRP ANTI-SLIP SHEETS & PANELS

GripClad® GRP anti-slip sheets and panels provide a simple, retrofit solution to slippery pathways, walkways or any other application. They are available in full sheet sizes or cut to your requirements, making them ideal for wet or icy weather, steep inclines, walkways, high-footfall footbridges, or oily areas.  

The flat anti-slip sheets can be screwed, bolted, riveted or bonded onto surfaces including wood, concrete, steel, chequer plates and even on open mesh grating.

Benefits of GRP Anti-Slip Sheets and Panels

• Easy to install
• Instant protection from slips and trips
• Highly functional
• Incredibly tough and durable
• Perfect as a short or long term solution

Our GRP Anti-Slip Sheets & Panels

Available in Medium Coarse Grade 16 Available in Standard 4.0mm Colours: Black, Light Grey, Yellow, Beige Standard sizes available:

• 3000mm x 1220mm x 4.0mm
• 2440mm x 1220mm x 4.0mm
• 2400mm x 1200mm x 4.0mm
• 2000mm x 1000mm x 4.0mm
• 1220mm x 1220mm x 4.0mm
• 800mm x 1200mm x 4.0mm

GripClad® GRP Anti-Slip Sheets and Panels have seen effective use in a huge variety of locations, markets and industries including:

• Production areas
• Walkways
• Loading Bays
• Access Ramps
• Factory Production Lines
• Entrance Ways
• Worker access to machinery
• Footbridges
• Washrooms
• Pedestrian bridge

• PTV Test Reading Dry: 71 and PTV Reading Wet: 63

Slip resistance properties of flooring materials are covered by various standards with Europe. BS7976 describes the specification, operation and calibration of the Pendulum test, used for assessment of floor surface slipperiness under both dry and contaminated conditions. The results are reported as Pendulum Test Value or Slip Resistance Value and are approximately 100 times the coefficient of friction. The Pendulum test is used routinely by the Health & Safety Laboratory on behalf of HSE.

Four S Pendulum Value	Potential for Slip
Above 65	Extremely Low
35 to 65	Low
25 to 65
25 and Below	High

View our Coefficient of Friction Test for our anti-slip sheets.

The GRP anti-slip flat sheets can be screwed, bolted, riveted or bonded onto surfaces including wood, concrete, steel, chequer plates and even on open mesh grating

ALL GRIPCLAD ® Anti Slip Stair Tread Covers, Flat Sheets, and Nosings can be easily and quickly installed.

Adhesive & Screws

• Obviously, the surface needs to be clean, dry, and free from any loose and friable material.

• Check that the product/s actually fit freely and that they sit flat down on the surface. Simple trimming on site to suit, ideally using a skill saw with a 4mm diamond blade or an angle grinder with a 1mm blade.

• Protect your eyes with goggles and gloves are worn at all times when any form of cutting is involved.

• Apply an approx. 8mm bead (this may need to be increased depending on the substrate conditions) of the high strength gap filling adhesive around the periphery of the underside of the stair tread covers approx. 25mm in from the edges plus diagonal bead along the depth, The adhesive is best applied using a skeleton gun.

• Place the panel firmly to the substrate to ensure adequate transfer of adhesive (depending on the size of the bead, this will elevate the sheet by approximately 1-1.5mm). A firm bond will be achieved in about one hour under normal circumstances and conditions.

• Mechanical fixing using a choice of screws depending on the surface,  (1) 40mm Stainless Steel with RAw Plug (2) 40mm BZP Screws self Drilling point and self countersinking (3) 25mm Tek Screw HD for Chequer plate (4) 25mm Self -Drilling to Thinner metals